Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Inspection for Bay Ridge Homeowners
Most chimney problems stay invisible until they cause a fire, a carbon monoxide scare, or a water stain on the ceiling below the flue. An inspection is how you find out what’s actually going on inside the system before any of that happens. Chimney Sweep Bay Ridge is a chimney-only specialist, so our technicians look at flues, fireboxes, crowns and caps every working day, and they have up to 11 years of experience reading what those parts tell them. We check with a camera, we show you the photos, and we tell you honestly when nothing needs doing. Same-day appointments are often available in Bay Ridge. Call (855) 551-0049 to book a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
What Our Chimney Inspection Service Includes
A chimney inspection isn’t one fixed procedure. The National Fire Protection Association sets out three levels, and which one you need depends on what’s happening with the chimney. Here’s how we handle each, plus the specialized checks that fall under them.
Level 1 Inspection
A Level 1 inspection covers the readily accessible parts of the chimney: the firebox, damper, flue interior as far as can be seen, and the visible exterior parts like the cap and crown. It’s the right starting point when your chimney is in regular use and nothing has changed – same appliance, same fuel, no recent damage or repairs. We perform this check as part of every routine sweep and note the condition of each component so you have a record of the system over time. If we see something the basic view can’t explain, we tell you rather than guess.
Level 2 Inspection
A Level 2 inspection goes further, using a camera to examine the flue from top to bottom and looking closely at accessible portions of the attic, crawlspace and other concealed areas. You need this level when something has changed: a new appliance, a switch from wood to gas, a chimney fire, a chimney that has been struck by lightning, or a property sale or transfer. In Bay Ridge’s rowhouse stock, where flues often share party walls with neighboring units, this closer look matters. We run the camera, take stills, and hand you a photo report you can actually read.
Level 3 Inspection
A Level 3 inspection is the most involved and is only warranted when a serious hazard is suspected and the lower levels can’t resolve it. It may involve opening up a wall or removing part of the chimney structure to reach areas that are otherwise inaccessible. We don’t jump to this. We only recommend a Level 3 after a camera inspection has pointed to a specific problem that requires opening the chimney to confirm. If that happens, we explain what will be opened, why, and what we expect to find before any work begins.
Camera Inspection
A camera inspection sends a lit video camera down the flue to show what no eye can see from below or above. It reveals cracks, gaps in the tile joints, spalling, blockages, and any liner damage hidden in the middle of a run. Every camera inspection at Chimney Sweep Bay Ridge includes a photo report. You see the same footage we do, so nothing gets recommended that you can’t verify for yourself.
Flue Inspection
Flue inspection focuses specifically on the passage that carries smoke and gases out of your home. We check its size relative to the appliance, its straightness and offsets, and the condition of the liner or tile throughout. This is where HeatShield ceramic resurfacing often matters: some cracked liners can be restored rather than replaced entirely, and a proper flue inspection tells you which is the right call. We measure first and discuss options second.
Real Estate Inspection
A real estate inspection is a Level 2 evaluation timed around a property sale, and it’s often the most useful document in a transaction. It tells the buyer what the chimney system is, what condition it’s in, and what work, if any, is genuinely needed. We produce a written report with photos that both sides can rely on, and we’re clear about what’s a real safety issue versus what’s cosmetic or can safely wait.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Inspection
When we inspect, we’re also looking at what’s already installed. Chimneys are commonly fitted with components from HeatShield, Gelco, Olympia Chimney and Famco, and knowing how each one ages changes what we look for. HeatShield ceramic resurfacing, for example, can show wear patterns in the joints that tell us how much service life a restored liner has left, so we know when to recommend resurfacing again and when a different approach makes more sense.
Gelco products and Olympia Chimney components both show up in caps and crowns, and a failing cap or crown is one of the two most common points where water gets into a chimney. In a Bay Ridge rowhouse, a small leak at the crown runs straight into the masonry and the ceilings below. Famco parts are equally familiar, and we inspect them with the same eye. Whether you have HeatShield, Gelco, Olympia Chimney, Famco or any other make, we can help.
Signs You Need Chimney Inspection Right Now
Some of these are obvious. Others are easy to miss until they’ve been building for a while. If any of them sound familiar, book an inspection rather than waiting for the next sweep.
- You smell smoke in the room when the fire is lit. Draft problems often trace back to a blocked flue, a damaged liner or an undersized flue. A camera check shows the cause in minutes instead of guesswork.
- There’s creosote buildup you can see or smell. Creosote is what fuels a chimney fire, and heavy buildup is a warning to stop using the fireplace until the flue is cleaned and checked. A routine sweep is the way to deal with it, and the inspection happens at the same time.
- You’ve had a chimney fire, even a small one. A fire can crack tiles and damage a liner without any obvious sign from the outside. A Level 2 inspection is warranted after any chimney fire, no matter how brief.
- Water stains, rust or crumbling mortar are showing. These are signs of water entering at the crown or cap. Both are the most common water-intrusion points, and catching them early is the difference between a straightforward repair and a structural problem.
- A new appliance is going in, or you’re buying the home. Changing from wood to gas, adding a stove, or buying or selling a property all call for a Level 2 inspection. It’s the standard against which everyone from buyers to insurers reads the chimney.
Our Chimney Inspection Process – Step by Step
- 1
We talk through the system first. Before we climb anything, we ask what you’ve noticed, how often the fireplace is used, what fuel, and whether anything has changed. That conversation shapes which inspection level is right and saves you paying for a deeper check you don’t need.
- 2
We inspect from the firebox up. We open the damper, check the firebox and smoke chamber, and view as far up the flue as we can see. This gives us the starting picture before the camera goes in.
- 3
We run the camera down the flue. A lit camera shows cracks, gaps, blockages and the true state of the liner. We capture stills and video and narrate what we’re seeing as we go, so you understand the findings as they come up.
- 4
We check the exterior – crown, cap, flashing and mortar. Water intrusion starts here, and the crown and cap are the two points where it most often gets in. We confirm whether they’re doing their job or letting water past.
- 5
We write up the report and walk you through it. You get a photo report, a plain explanation of what needs attention now versus what can wait, and an honest recommendation. We do not recommend work without camera evidence you’ve seen yourself.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Inspection Cost in Bay Ridge?
An inspection is priced by the job, and the written estimate sets the final price. A typical Level 1 inspection in Bay Ridge runs $130 – $220 depending on how accessible the flue is and whether it’s paired with a sweep. A Level 2 inspection with camera runs $220 – $400, higher if there are offsets, a share of the party wall, or a longer flue run to thread. A real estate inspection runs $220 – $380 depending on the size and complexity of the property. Camera inspection alone is $175 – $295. Flue resurfacing evaluation with HeatShield, if a restore-versus-replace decision is needed, is quoted separately once the camera shows the liner condition.
Three factors move the price: the inspection level, flue complexity (bends and offsets cost more time to inspect than a straight run), and access to the roof. If you’re told you need thousands of dollars of liner or masonry work, ask to see the camera footage first – nothing should be recommended without it. Our estimate includes the camera, the photo report and the written findings. Call (855) 551-0049 for an exact quote.
Chimney Inspection Near Bay Ridge – Our Service Area
We serve Bay Ridge and the surrounding neighborhoods and communities: Dyker Heights, Borough Park, Sunset Park, Bensonhurst, Kensington, Midwood, Gravesend and South Beach, across the Verrazano to Rosebank, Stapleton and St. George on Staten Island. Scheduling is based on route and job type, and most inspections can be arranged within a short window. If you’re in a neighboring area, ask when you call.
If you want a closer look at how we handle a nearby community, see our chimney inspection page for Dyker Heights or the chimney inspection page for Borough Park.
Serving Bay Ridge, NY – Our Local Coverage Area
We serve Bay Ridge and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Inspection in Bay Ridge
A chimney inspection is a formal evaluation of your chimney’s condition, covering the firebox, flue, liner, crown, cap and visible exterior. Which level you need depends on what’s changed – a Level 1 for routine checks, a Level 2 with a camera for changes or sales, a Level 3 only when a serious problem needs opening up. Call (855) 551-0049 for an exact quote – estimates are free.
A Level 1 inspection typically takes under an hour, while a Level 2 with camera inspection usually takes one to two hours depending on flue access and roof access. A real estate inspection may run longer because of the written report. The best way to know is to describe your setup when you call.
Typical estimates are $130 – $220 for a Level 1, $220 – $400 for a Level 2 with camera, and $175 – $295 for a camera inspection alone, with the written estimate setting the final price. The level, flue complexity and roof access are what move the number. Call (855) 551-0049 for an exact quote – estimates are free.
Yes. We inspect chimneys fitted with HeatShield ceramic resurfacing, Gelco and Olympia Chimney components, Famco parts and other makes. We know how each one ages and where the weak points show up. Whether your chimney has one of those brands or none of them, we can help.
Same-day inspections are often available, depending on route and demand. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday, closed Saturday. Call (855) 551-0049 and we’ll book you into the earliest opening.
An inspection is a diagnostic service, so warranty terms vary by what’s found and what work follows. If repairs are recommended, the written estimate will spell out the terms for that specific work. Ask when you book and we’ll confirm in writing.
Clear the area in front of the fireplace and make sure we can reach the roof and any attic or crawlspace access. If you have prior inspection reports or camera footage, have them ready – it helps us understand the history. Do not to light a fire for at least 24 hours before the visit. Call (855) 551-0049 if you’re unsure about anything.
Schedule Your Chimney Inspection Service in Bay Ridge Today
Book a chimney inspection and you’ll know exactly where your system stands – with photos you can see, a plain report and no pressure to do anything that isn’t warranted. Our team handles only chimney and fireplace work, so the inspection and any repair stay with the same specialists. Call (855) 551-0049 for a free, no-obligation estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Written by the team at Chimney Sweep Bay Ridge.