Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Bay Ridge Homeowners
Water is the quiet enemy of a Bay Ridge chimney. It gets into the brick through a cracked crown, a failed flashing seam, or mortar that has weathered through decades of freeze-thaw cycles, and it does its damage from the inside out. We focus on chimney and fireplace systems exclusively, so we know where these houses leak and what stops it. Our technicians have up to 11 years of experience, and they diagnose before they quote: nothing is recommended without a camera inspection and a photo report you can see for yourself. A sweep or a repair is booked, not rushed, but we do offer same-day service when the schedule allows. Call (855) 551-0049 to start.
What Our Chimney Repair Service Includes
Chimney repair covers a wide range of problems, and the right fix depends entirely on what the inspection finds. Here’s what each of our repair services addresses.
Mortar Repointing
Mortar is the softer material between the bricks, and it’s designed to wear out first so the brick survives. When the joints recede and crumble, the chimney loses structural grip and water finds a path inside. We rake out the failed mortar to the right depth and repack the joints, matching the existing profile so the repair blends into the chimney instead of reading as a patch.

Spalling Brick Repair
Spalling is brick that has flaked, peeled, or lost its face entirely, usually after trapped moisture freezes and pushes outward. You’ll see brick dust and fragments collecting at the base of the chimney, and the exposed inner material absorbs water even faster than the original face did. We replace the damaged units with brick matched to the rest of the chimney and address the moisture source that caused the spalling in the first place, because new brick over the same leak fails the same way.

Chimney Waterproofing
Waterproofing is a breathable sealer applied to the masonry after repairs are complete, and it’s the single most cost-effective step a homeowner can take to slow future decay. It keeps rain out while still allowing moisture vapor to escape, which matters because a sealer that traps vapor makes spalling worse. We apply it once the brick and mortar are sound and fully cured, so it’s protecting a healthy chimney rather than sealing in a problem.

Flashing Repair
Flashing is the metal that seals the joint where the chimney passes through the roof, and it’s the most common source of chimney leaks we find. Old flashing pulls away, tar patches crack, and water runs straight down the masonry into the attic or ceiling below. We reset or replace the flashing, tie it into the roof properly, and check the counterflashing at the same time, since the two parts only work as a pair.
Chimney Rebuilding
When a chimney is leaning, has lost multiple courses of brick, or has damage that runs beyond what repointing can fix, rebuilding the affected section is the honest answer. Rebuilding sounds drastic, but it’s often limited to the portion above the roofline, not the whole stack. We match the existing brick and mortar as closely as possible, and we rebuild only the section that needs it, because tearing down a sound chimney to reach a bad one is wasted money for the homeowner.
Tuckpointing
Tuckpointing is precision mortar work on visible joints, and it’s the right choice when the chimney is structurally fine but the joints are unsightly or starting to fail. We cut the joints cleanly, pack them with mortar matched for color and consistency, and tool them to a finish that suits the surrounding masonry. It’s part cosmetic, part protective, and on a Bay Ridge home with a front-facing chimney it’s often the difference between a chimney that looks maintained and one that looks neglected.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Brands We Service for Chimney Repair
We work with professional-grade chimney materials, and that matters when the repair involves a liner, a crown, or a component that has to hold up for decades rather than seasons. HeatShield is our go-to for flue liner restoration: it’s a ceramic resurfacing system that repairs cracks and gaps inside the flue without pulling the whole liner, and it’s a genuine alternative to full relining when the existing liner still has enough structure to build on. We also install and service Gelco products for crown and top-sealing work, where a properly formed, correctly sloped crown decides whether water sheds off the chimney or runs into it.
On liner replacements, DuraFlex flexible liner systems let us work with chimneys that have bends, offsets, or a tight path down the flue, the configurations where rigid liners often can’t make the turn. Finishing work and accessories come from Olympia Chimney, a familiar name to anyone who has had chimney work done before. Whether your chimney already has HeatShield, Gelco, DuraFlex, or Olympia Chimney components, or it’s working with something else entirely, we can help, and we’ll tell you plainly if what’s there is still sound.
Signs You Need Chimney Repair Right Now
Some chimney problems are cosmetic and can wait for a scheduled visit. Others are active damage that gets worse every time it rains. Here’s how to tell the difference.
- Brick fragments or grit on the roof or ground. Spalling brick sheds its face, and what you’re seeing is the outer layer of the chimney failing. It means moisture is already inside the masonry, and each freeze-thaw cycle pushes more of it off.
- White staining on the brick. That chalky deposit is called efflorescence, and it’s evidence that water is moving through the masonry and leaving mineral salts behind as it dries. It’s a symptom, not the problem itself, so it needs a proper look.
- Damp patches on the ceiling or in the attic near the chimney. This usually points to flashing that has failed or a crown that no longer sheds water away from the flue. Left alone, that moisture reaches framing, insulation, and eventually the interior finishes.
- Crumbling mortar joints you can dig out with a screwdriver. Receded mortar is the chimney’s structural grip letting go. It’s a repointing job while it’s confined to the joints; it becomes a rebuilding job if the brick starts to move.
- A chimney that leans or a crown that’s cracked through. Either of these warrants prompt attention. A cracked crown lets water straight into the flue, and a lean is a structural warning that shouldn’t be scheduled for later.
If you’re seeing any of these, we can also help with chimney repair nearby, and we’ll give you a straight answer about what’s urgent and what can wait.
Our Chimney Repair Process – Step by Step
- 1
Inspection first, always. We start with a camera inspection of the flue and a close look at the exterior masonry, crown, flashing, and cap. You see the findings in a photo report, so the recommendations are tied to evidence rather than a sales pitch.
- 2
A written estimate that spells out the work. We list what needs repair, what it will cost, and what the job involves. If something can safely wait a season, we say so. The written estimate sets the final price.
- 3
Scheduled repair with proper materials. We book the work and specify materials matched to the job: HeatShield for liner restoration, matched brick and mortar for repointing and rebuilding, correct sealants for flashing. The local pro working on your chimney is licensed and insured as their state requires.
- 4
Careful workmanship on the roof. Chimney work involves heights and, on some jobs, working around the roofline. We protect the roof surface, keep the work area clean, and never cut corners on safety just to save time.
- 5
Final check and clear explanation. After the repair, we walk you through what was done, confirm the fix is sound, and leave you with a clear picture of your chimney’s condition. No handoff to a different contractor, because the same company that inspects the chimney also repairs it.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Chimney Repair Cost in Bay Ridge?
Typical chimney repair in Bay Ridge runs anywhere from a few hundred dollars for a focused repointing or flashing repair to several thousand for a partial rebuild, depending on how far the damage has spread. Here’s a rough guide to the common scenarios.
| Repair Type | Typical Estimated Cost | What Drives the Price |
|---|---|---|
| Mortar repointing (partial) | $400 – $900 | Number of joints, height, access |
| Flashing repair | $300 – $800 | Roof type, extent of failed flashing |
| Spalling brick replacement | $500 – $1,500 | Number of bricks, matching work |
| Chimney waterproofing | $350 – $700 | Square footage of masonry |
| Crown repair or rebuild | $500 – $1,200 | Crown size, rebuild vs. resurface |
| Partial chimney rebuild | $2,000 – $6,000 | Courses involved, brick matching |
Price is driven mostly by how much of the chimney is affected and how easy it is to reach. A rear chimney behind a steep roof takes more setup than one you can reach from a flat section. The reliable way to avoid overpaying is to insist on camera evidence and a written estimate before anyone starts. That’s what our free estimate gives you: a clear scope, a flat price agreed before booking, and a written document that sets the final price. If a quote sounds high, ask to see the photos.
Chimney Repair Near Bay Ridge – Our Service Area
We schedule chimney work across Bay Ridge and the surrounding neighborhoods, including Dyker Heights, Borough Park, Sunset Park, Bensonhurst, and Gravesend. For nearby work, we also cover the chimney repair needs of Borough Park homeowners. We answer 24/7 and dispatch crews Sunday through Friday, 7am to 7pm. Call for current availability in your area; estimates are free.
Serving Bay Ridge, NY – Our Local Coverage Area
We serve Bay Ridge and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Chimney Repair in Bay Ridge
Chimney repair is the work of restoring the structural and moisture-protection parts of a chimney: the masonry, mortar joints, crown, flashing, and flue lining. It’s separate from a sweep, which removes creosote and soot from inside the flue. A chimney can be clean and still need repair, because the two problems fail independently. If you’re unsure which one you need, start with an inspection and let the findings decide. Call (855) 551-0049 for an exact quote; estimates are free.
Most focused repairs, like repointing a section of mortar or resetting flashing, are completed in a single visit. Larger work takes longer: waterproofing needs the masonry to be sound and fully cured first, and a partial rebuild can run multiple days depending on the number of courses and material matching. Your written estimate will give you a realistic timeframe for your specific job before anything is booked.
Typical chimney repair in Bay Ridge ranges from about $300 for a small flashing fix to $6,000 for a partial rebuild, with most common repairs falling between $400 and $1,500. The written estimate sets the final price, and it’s free. Nothing is recommended without camera evidence you can review, so you can see what drives the number. Call (855) 551-0049 for an exact quote.
Yes. We work with HeatShield ceramic resurfacing for liner restoration, Gelco for crown and top-sealing work, DuraFlex flexible liners for flues with bends or offsets, and Olympia Chimney components for finishing and accessory work. If we find one of these installed and still sound, we’ll tell you so rather than replace it. Whether you have one of these brands or any other make, we can help.
Yes, same-day service is available when the schedule allows. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening. The urgency with chimney work is usually seasonal, ahead of burning season, more than hourly, so booking early in the season is the practical move.
Warranty terms depend on the type of repair and the materials used, so they’re stated in writing in your estimate rather than generalized here. Repointing, flashing work, and liner work each carry different expectations, and you should see them before you approve the job. Ask for the written terms up front; that’s a fair question and any contractor should answer it plainly.
Clear access to the fireplace or stove opening, make sure the chimney is cool, and note any symptoms you’ve seen: damp patches, crumbling mortar, or grit on the roof. Keep pets and children away from the work area while the technician is on the roof. That’s all the preparation usually needed, and the inspection report will tell you what comes next.
Schedule Your Chimney Repair Service in Bay Ridge Today
If you’re seeing crumbling mortar, damp patches, or brick fragments, it’s worth an inspection before winter. Our technicians have up to 11 years of experience, the inspection includes a camera report and photo evidence, and the estimate is free with no obligation. Call (855) 551-0049. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday. You’ll get straight answers and a written price before any work begins.
Written by the team at Chimney Sweep Bay Ridge.